Enclosure Install
Moderate1 hr16 steps
Step 1 Fastener Oversights
- Caution: Unfortunately, some mistakes were made with the fasteners that were included with some of the enclosure upgrades that were shipped as part of the kickstarter batch.
- Note: You may be missing:
- M4 x 25mm bolt (x4)
- M4 x 10mm Counter Sunk Bolt (x1)
- Reminder: Please complete this form here, and we'll have these sent out, alternatively you can source locally for a quicker solution.
Loading comments…
Step 2 Fume Filter
- Note: Find the filter case, carbon filters and HEPA cloth.
- Place a carbon filter onto the centre of the HEPA cloth.
- Cut the 4 squares from the corners as shown.
- Push the carbon and HEPA filters into the filter case as shown.
Loading comments…
Step 3 Trimming the Excess HEPA Cloth
- Trim away the excess HEPA cloth.
Loading comments…
Step 4 Filter to Back Panel
- Remove the backing paper from the back panel.
- Fix the fume filter assembly to the back panel, with the 60mm fan on the other side.
- M4 x 25mm Bolt
- Make sure that the fan is fixed sticker side up.
Loading comments…
Step 5 Bolts to Back Panel
- Note: Losely fasten on:
- M4 x 6mm Bolts
- M4 T-Nuts
- Reminder: Make sure that the bolts are on the fan side.
Loading comments…
Step 6 Side Panel Prep.
- Note: Begin by peeling away the protective covering from both sides of the side panels.
- As with the back panels, losely fasten:
- M4 x 6mm Bolt
- M4 T-Nut
- Create mirrored assemblies of the two side panels.
Loading comments…
Step 7 Front Panel Prep. - Handle
- Fix the handle onto the front panel.
- M4 x 10mm Counter Sunk Bolt
- M4 Button Magnet
Loading comments…
Step 8 Front Panel Prep. - Hinges
- Fix the hinges as shown to the front panel.
- M4 x 6mm
- M4 T-Nut
- M4 x 10mm
- M4 Nyloc Nut
Loading comments…
Step 9 Back Panel Install
- Fix the Back Panel to the rear of the printer, with the fan on the outside.
- Feed the cable through the wiring loom and into the base.
- Connect the fan to the control board as shown.
Loading comments…
Step 10 Side Panels Install
- Mount the side panels to the side of the printer.
- Orientate so that the spool holder cut out points to the rear of the machine.
Loading comments…
Step 11 Front Panel Install
- Fix the door hinges to the front of the printer.
Loading comments…
Step 12 Magnetic Latch
- Prepare the enclosure latch with an M4x6mm bolt and M4 T-nut.
- Align the enclosure latch with the magnet on the door handle and fix it in place on the inside of the frame.
Loading comments…
Step 13 Roof Prep
- Take the roof and lay it down as shown.
- Bend all of the tabs up.
Loading comments…
Step 14 Roof Panel
- Peel the protective sheet from both sides of the roof panel.
- Drop it onto the raised tabs.
- Bend the tabs back down as shown to secure the panel.
Loading comments…
Step 15 Securing the Roof
- Due to the paint that was applied on both the roof and top panel, the tabs may need filing down to get a proper fit.
- Drop the roof into the slots on the top panel, push back to secure.
- Before fixing the roof, the PTFE tubes need to be fed through the slots on the side as shown.
Loading comments…
Step 16 Using the Fume Fan
- Note: Include M106 P2 to your start Gcode to activate the fan.
- Note: Include M107 P2 to your end Gcode to turn off the fan.
Loading comments…
