# P5_PrusaSlicer_config_bundle.ini
# generated by PrusaSlicer 2.9.4 on 2026-06-03 at 10:24:44 UTC
[print:ProForge Default] arc_fitting = emit_center automatic_extrusion_widths = 0 automatic_infill_combination = 0 automatic_infill_combination_max_layer_height = 100% avoid_crossing_curled_overhangs = 0 avoid_crossing_perimeters = 0 avoid_crossing_perimeters_max_detour = 0 bed_temperature_extruder = 0 bottom_fill_pattern = monotonic bottom_solid_layers = 4 bottom_solid_min_thickness = 0 bridge_acceleration = 0 bridge_angle = 0 bridge_flow_ratio = 1 bridge_speed = 45 brim_separation = 0 brim_type = outer_only brim_width = 0 compatible_printers = compatible_printers_condition = complete_objects = 0 custom_parameters_print = default_acceleration = 8000 dont_support_bridges = 1 draft_shield = disabled elefant_foot_compensation = 0 enable_dynamic_overhang_speeds = 1 ensure_vertical_shell_thickness = enabled external_perimeter_acceleration = 0 external_perimeter_extrusion_width = 0.45 external_perimeter_speed = 75% external_perimeters_first = 0 extra_perimeters = 1 extra_perimeters_on_overhangs = 0 extrusion_width = 0.45 fill_angle = 45 fill_density = 20% fill_pattern = grid first_layer_acceleration = 0 first_layer_acceleration_over_raft = 0 first_layer_extrusion_width = 0.42 first_l
fill_density = 20% fill_pattern = grid first_layer_acceleration = 0 first_layer_acceleration_over_raft = 0 first_layer_extrusion_width = 0.42 first_layer_height = 0.2 first_layer_infill_speed = 0 first_layer_speed = 50 first_layer_speed_over_raft = 30 fuzzy_skin = none fuzzy_skin_point_dist = 0.8 fuzzy_skin_thickness = 0.3 gap_fill_enabled = 1 gap_fill_speed = 50 gcode_comments = 0 gcode_label_objects = firmware gcode_resolution = 0.0125 gcode_substitutions = infill_acceleration = 16000 infill_anchor = 600% infill_anchor_max = 50 infill_every_layers = 1 infill_extruder = 1 infill_extrusion_width = 0.45 infill_first = 0 infill_overlap = 40% infill_speed = 200 inherits = interface_shells = 0 interlocking_beam = 0 interlocking_beam_layer_count = 2 interlocking_beam_width = 0.8 interlocking_boundary_avoidance = 2 interlocking_depth = 2 interlocking_orientation = 22.5 ironing = 0 ironing_flowrate = 15% ironing_spacing = 0.1 ironing_speed = 15 ironing_type = top layer_height = 0.2 max_print_speed = 500 max_volumetric_extrusion_rate_slope_negative = 0 max_volumetric_extrusion_rate_slope_positive = 0 max_volumetric_speed = 0 min_bead_width = 85% min_feature_size = 25% min_skirt_length =
_negative = 0 max_volumetric_extrusion_rate_slope_positive = 0 max_volumetric_speed = 0 min_bead_width = 85% min_feature_size = 25% min_skirt_length = 20 mmu_segmented_region_interlocking_depth = 0 mmu_segmented_region_max_width = 0 notes = only_one_perimeter_first_layer = 0 only_retract_when_crossing_perimeters = 0 ooze_prevention = 0 output_filename_format = [input_filename_base].gcode over_bridge_speed = 0 overhang_speed_0 = 30 overhang_speed_1 = 30 overhang_speed_2 = 40 overhang_speed_3 = 50 overhangs = 1 perimeter_acceleration = 0 perimeter_extruder = 1 perimeter_extrusion_width = 0.45 perimeter_generator = arachne perimeter_speed = 150 perimeters = 3 post_process = print_settings_id = raft_contact_distance = 0.1 raft_expansion = 1.5 raft_first_layer_density = 90% raft_first_layer_expansion = 3 raft_layers = 0 resolution = 0 scarf_seam_entire_loop = 0 scarf_seam_length = 20 scarf_seam_max_segment_length = 1 scarf_seam_on_inner_perimeters = 0 scarf_seam_only_on_smooth = 1 scarf_seam_placement = nowhere scarf_seam_start_height = 0% seam_gap_distance = 15% seam_position = nearest single_extruder_multi_material_priming = 0 skirt_distance = 3 skirt_height = 1 skirts = 2 slice_cl
0% seam_gap_distance = 15% seam_position = nearest single_extruder_multi_material_priming = 0 skirt_distance = 3 skirt_height = 1 skirts = 2 slice_closing_radius = 0.049 slicing_mode = regular small_perimeter_speed = 60 solid_infill_acceleration = 0 solid_infill_below_area = 70 solid_infill_every_layers = 0 solid_infill_extruder = 1 solid_infill_extrusion_width = 0.45 solid_infill_speed = 150 spiral_vase = 0 staggered_inner_seams = 0 standby_temperature_delta = -5 support_material = 1 support_material_angle = 0 support_material_auto = 0 support_material_bottom_contact_distance = 0 support_material_bottom_interface_layers = -1 support_material_buildplate_only = 1 support_material_closing_radius = 2 support_material_contact_distance = 0.2 support_material_enforce_layers = 0 support_material_extruder = 0 support_material_extrusion_width = 0.45 support_material_interface_contact_loops = 0 support_material_interface_extruder = 0 support_material_interface_layers = 3 support_material_interface_pattern = rectilinear support_material_interface_spacing = 0 support_material_interface_speed = 100% support_material_pattern = rectilinear support_material_spacing = 2.5 support_material_speed =
ce_spacing = 0 support_material_interface_speed = 100% support_material_pattern = rectilinear support_material_spacing = 2.5 support_material_speed = 45 support_material_style = organic support_material_synchronize_layers = 0 support_material_threshold = 25 support_material_with_sheath = 1 support_material_xy_spacing = 50% support_tree_angle = 40 support_tree_angle_slow = 25 support_tree_branch_diameter = 2 support_tree_branch_diameter_angle = 5 support_tree_branch_diameter_double_wall = 3 support_tree_branch_distance = 1 support_tree_tip_diameter = 0.8 support_tree_top_rate = 15% thick_bridges = 1 thin_walls = 1 top_fill_pattern = monotonic top_infill_extrusion_width = 0.4 top_one_perimeter_type = none top_solid_infill_acceleration = 0 top_solid_infill_speed = 110 top_solid_layers = 4 top_solid_min_thickness = 0 travel_acceleration = 20000 travel_short_distance_acceleration = 0 travel_speed = 400 travel_speed_z = 0 wall_distribution_count = 1 wall_transition_angle = 10 wall_transition_filter_deviation = 25% wall_transition_length = 100% wipe_tower = 1 wipe_tower_acceleration = 0 wipe_tower_bridging = 10 wipe_tower_brim_width = 2 wipe_tower_cone_angle = 25 wipe_tower_extra_flow = 1
00% wipe_tower = 1 wipe_tower_acceleration = 0 wipe_tower_bridging = 10 wipe_tower_brim_width = 2 wipe_tower_cone_angle = 25 wipe_tower_extra_flow = 100% wipe_tower_extra_spacing = 100% wipe_tower_extruder = 0 wipe_tower_no_sparse_layers = 0 wipe_tower_width = 25 xy_size_compensation = 0
[filament:ABS] bed_temperature = 100 bridge_fan_speed = 35 chamber_minimal_temperature = 0 chamber_temperature = 0 compatible_printers = compatible_printers_condition = compatible_prints = compatible_prints_condition = cooling = 1 cooling_perimeter_transition_distance = 0 cooling_slowdown_logic = uniform_cooling custom_parameters_filament = "" disable_fan_first_layers = 1 enable_dynamic_fan_speeds = 0 end_filament_gcode = "; Filament-specific end gcode \n;END gcode for filament" extrusion_multiplier = 0.9 fan_always_on = 1 fan_below_layer_time = 15 filament_abrasive = 0 filament_colour = #C0362E filament_cooling_final_speed = 3.4 filament_cooling_initial_speed = 2.2 filament_cooling_moves = 4 filament_cost = 0 filament_density = 1.24 filament_deretract_speed = nil filament_diameter = 1.75 filament_infill_max_crossing_speed = 0 filament_infill_max_speed = 0 filament_load_time = 0 filament_loading_speed = 28 filament_loading_speed_start = 3 filament_max_volumetric_speed = 0 filament_minimal_purge_on_wipe_tower = 15 filament_multitool_ramming = 0 filament_multitool_ramming_flow = 10 filament_multitool_ramming_volume = 10 filament_notes = "" filament_purge_multiplier = 100% filamen
l_ramming = 0 filament_multitool_ramming_flow = 10 filament_multitool_ramming_volume = 10 filament_notes = "" filament_purge_multiplier = 100% filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6" filament_retract_before_travel = nil filament_retract_before_wipe = nil filament_retract_layer_change = nil filament_retract_length = nil filament_retract_length_toolchange = nil filament_retract_lift = nil filament_retract_lift_above = nil filament_retract_lift_below = nil filament_retract_restart_extra = nil filament_retract_restart_extra_toolchange = nil filament_retract_speed = nil filament_seam_gap_distance = nil filament_settings_id = "" filament_shrinkage_compensation_xy = 0% filament_shrinkage_compensation_z = 0% filament_soluble = 0 filament_spool_weight = 0 filament_stamping_distance = 0 filament_stamping_loading_speed = 20 filament_toolchange_delay = 0 filament_travel_lift_before_obstacle = nil filament_travel_max_lift = nil filament_travel_ramping_lift = nil filament_travel_slope = nil filament_type = ABS filament_unload_time = 0 filament_unloading_spee
vel_max_lift = nil filament_travel_ramping_lift = nil filament_travel_slope = nil filament_type = ABS filament_unload_time = 0 filament_unloading_speed = 90 filament_unloading_speed_start = 100 filament_vendor = (Unknown) filament_wipe = nil first_layer_bed_temperature = 100 first_layer_temperature = 240 full_fan_speed_layer = 3 idle_temperature = nil inherits = max_fan_speed = 35 min_fan_speed = 25 min_print_speed = 10 overhang_fan_speed_0 = 0 overhang_fan_speed_1 = 0 overhang_fan_speed_2 = 0 overhang_fan_speed_3 = 0 slowdown_below_layer_time = 5 start_filament_gcode = "; Filament gcode\n" temperature = 230
[filament:PLA] bed_temperature = 50 bridge_fan_speed = 75 chamber_minimal_temperature = 0 chamber_temperature = 0 compatible_printers = compatible_printers_condition = compatible_prints = compatible_prints_condition = cooling = 1 cooling_perimeter_transition_distance = 0 cooling_slowdown_logic = uniform_cooling custom_parameters_filament = "" disable_fan_first_layers = 1 enable_dynamic_fan_speeds = 0 end_filament_gcode = "; Filament-specific end gcode \n;END gcode for filament\n" extrusion_multiplier = 0.95 fan_always_on = 1 fan_below_layer_time = 60 filament_abrasive = 0 filament_colour = #29B2B2 filament_cooling_final_speed = 3.4 filament_cooling_initial_speed = 2.2 filament_cooling_moves = 4 filament_cost = 0 filament_density = 1.1 filament_deretract_speed = nil filament_diameter = 1.75 filament_infill_max_crossing_speed = 0 filament_infill_max_speed = 0 filament_load_time = 0 filament_loading_speed = 28 filament_loading_speed_start = 3 filament_max_volumetric_speed = 0 filament_minimal_purge_on_wipe_tower = 10 filament_multitool_ramming = 0 filament_multitool_ramming_flow = 10 filament_multitool_ramming_volume = 10 filament_notes = "" filament_purge_multiplier = 100% filame
ol_ramming = 0 filament_multitool_ramming_flow = 10 filament_multitool_ramming_volume = 10 filament_notes = "" filament_purge_multiplier = 100% filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6" filament_retract_before_travel = nil filament_retract_before_wipe = nil filament_retract_layer_change = nil filament_retract_length = nil filament_retract_length_toolchange = 1 filament_retract_lift = nil filament_retract_lift_above = nil filament_retract_lift_below = nil filament_retract_restart_extra = nil filament_retract_restart_extra_toolchange = 2 filament_retract_speed = nil filament_seam_gap_distance = nil filament_settings_id = "" filament_shrinkage_compensation_xy = 0% filament_shrinkage_compensation_z = 0% filament_soluble = 0 filament_spool_weight = 0 filament_stamping_distance = 0 filament_stamping_loading_speed = 20 filament_toolchange_delay = 0 filament_travel_lift_before_obstacle = nil filament_travel_max_lift = nil filament_travel_ramping_lift = nil filament_travel_slope = nil filament_type = PLA filament_unload_time = 0 filament_unloading_speed =
_max_lift = nil filament_travel_ramping_lift = nil filament_travel_slope = nil filament_type = PLA filament_unload_time = 0 filament_unloading_speed = 90 filament_unloading_speed_start = 100 filament_vendor = (Unknown) filament_wipe = nil first_layer_bed_temperature = 50 first_layer_temperature = 200 full_fan_speed_layer = 3 idle_temperature = nil inherits = max_fan_speed = 65 min_fan_speed = 45 min_print_speed = 10 overhang_fan_speed_0 = 0 overhang_fan_speed_1 = 0 overhang_fan_speed_2 = 0 overhang_fan_speed_3 = 0 slowdown_below_layer_time = 1 start_filament_gcode = "; Filament gcode" temperature = 200
[printer:ProForge 5] autoemit_temperature_commands = 1 bed_custom_model = bed_custom_texture = bed_shape = 0x0,500x0,500x400,0x400 before_layer_gcode = between_objects_gcode = binary_gcode = 0 color_change_gcode = cooling_tube_length = 5 cooling_tube_retraction = 91.5 custom_parameters_printer = default_filament_profile = default_print_profile = deretract_speed = 0,0,0,0,0 end_gcode = _END_PRINT\n extra_loading_move = -2 extruder_clearance_height = 20 extruder_clearance_radius = 20 extruder_colour = #CA001E;#00C900;#2F35E3;#FFFF00;#FFB200 extruder_offset = 0x0,0x0,0x0,0x0,0x0 gcode_flavor = klipper high_current_on_filament_swap = 0 host_type = octoprint inherits = layer_gcode = machine_limits_usage = time_estimate_only machine_max_acceleration_e = 5000,5000 machine_max_acceleration_extruding = 5000,1250 machine_max_acceleration_retracting = 5000,1250 machine_max_acceleration_travel = 1500,1250 machine_max_acceleration_x = 40000,1000 machine_max_acceleration_y = 40000,1000 machine_max_acceleration_z = 100,200 machine_max_feedrate_e = 120,120 machine_max_feedrate_x = 600,200 machine_max_feedrate_y = 600,200 machine_max_feedrate_z = 15,12 machine_max_jerk_e = 3,2.5 machine_m
rate_e = 120,120 machine_max_feedrate_x = 600,200 machine_max_feedrate_y = 600,200 machine_max_feedrate_z = 15,12 machine_max_jerk_e = 3,2.5 machine_max_jerk_x = 10,10 machine_max_jerk_y = 10,10 machine_max_jerk_z = 1,0.4 machine_max_junction_deviation = 0,0 machine_min_extruding_rate = 0,0 machine_min_travel_rate = 0,0 max_layer_height = 0,0,0,0,0 max_print_height = 500 min_layer_height = 0.07,0.07,0.07,0.07,0.07 multimaterial_purging = 140 nozzle_diameter = 0.4,0.4,0.4,0.4,0.4 nozzle_high_flow = 0,0,0,0,0 parking_pos_retraction = 92 pause_print_gcode = PAUSE prefer_clockwise_movements = 0 print_host = printer_model = printer_notes = printer_settings_id = printer_technology = FFF printer_variant = printer_vendor = printhost_apikey = printhost_cafile = remaining_times = 0 retract_before_travel = 2,2,2,2,2 retract_before_wipe = 0%,0%,0%,0%,0% retract_layer_change = 1,1,1,1,0 retract_length = 1.5,1.5,1.5,1.5,1.5 retract_length_toolchange = 0,0,0,0,0 retract_lift = 0.4,0.4,0.4,0.4,0.4 retract_lift_above = 0,0,0,0,0 retract_lift_below = 0,0,0,0,0 retract_restart_extra = 0,0,0,0,0 retract_restart_extra_toolchange = 0,0,0,0,0 retract_speed = 50,50,50,50,50 silent_mode = 0 single_
elow = 0,0,0,0,0 retract_restart_extra = 0,0,0,0,0 retract_restart_extra_toolchange = 0,0,0,0,0 retract_speed = 50,50,50,50,50 silent_mode = 0 single_extruder_multi_material = 0 start_gcode = M140 S{first_layer_bed_temperature[current_extruder]} ; Set bed temp\nRESPOND MSG="Setting Bed Temp {first_layer_bed_temperature[current_extruder]}C..."\nM104 S150 T0 ; Set PH1 temp for probing\nRESPOND MSG="Setting PH1 Nozzle Temp 150C for TAP Probing..."\n{if is_extruder_used[1]}M104 T1 S{temperature[1]}{endif}\n{if is_extruder_used[2]}M104 T2 S{temperature[2]}{endif}\n{if is_extruder_used[3]}M104 T3 S{temperature[3]}{endif}\n{if is_extruder_used[4]}M104 T4 S{temperature[4]}{endif}\n\nG28 ; Home\nDOCK\nTEMPERATURE_WAIT SENSOR=heater_bed MINIMUM={first_layer_bed_temperature[current_extruder]}\nTEMPERATURE_WAIT SENSOR=extruder MINIMUM=150\nG28 Z ; Home Z\n\nRESPOND MSG="Performing Bed Scan..."\nBED_MESH_SCAN\n\nRESPOND MSG="Performing TAP Calibration..."\n_CAL_SELECT_T0 ; Select and wipe PH1\nTAP\nDOCK\nM104 S0 T0 ; Turn off PH1 after tap\n\n; Set temperatures for all used extruders (non-blocking)\n{if is_extruder_used[0]}M104 T0 S{first_layer_temperature[0]}{endif}\n{if is_extruder_used[1]}M1
t temperatures for all used extruders (non-blocking)\n{if is_extruder_used[0]}M104 T0 S{first_layer_temperature[0]}{endif}\n{if is_extruder_used[1]}M104 T1 S{first_layer_temperature[1]}{endif}\n{if is_extruder_used[2]}M104 T2 S{first_layer_temperature[2]}{endif}\n{if is_extruder_used[3]}M104 T3 S{first_layer_temperature[3]}{endif}\n{if is_extruder_used[4]}M104 T4 S{first_layer_temperature[4]}{endif}\n\n; Wait for each used extruder to reach or exceed target temp\n{if is_extruder_used[0]}TEMPERATURE_WAIT SENSOR=extruder MINIMUM={first_layer_temperature[0]}{endif}\n{if is_extruder_used[1]}TEMPERATURE_WAIT SENSOR=extruder1 MINIMUM={first_layer_temperature[1]}{endif}\n{if is_extruder_used[2]}TEMPERATURE_WAIT SENSOR=extruder2 MINIMUM={first_layer_temperature[2]}{endif}\n{if is_extruder_used[3]}TEMPERATURE_WAIT SENSOR=extruder3 MINIMUM={first_layer_temperature[3]}{endif}\n{if is_extruder_used[4]}TEMPERATURE_WAIT SENSOR=extruder4 MINIMUM={first_layer_temperature[4]}{endif}\n\n; Prime each used extruder\n{if is_extruder_used[0]}_PRIME_PH1{endif}\n{if is_extruder_used[1]}_PRIME_PH2{endif}\n{if is_extruder_used[2]}_PRIME_PH3{endif}\n{if is_extruder_used[3]}_PRIME_PH4{endif}\n{if is_extruder_
if}\n{if is_extruder_used[1]}_PRIME_PH2{endif}\n{if is_extruder_used[2]}_PRIME_PH3{endif}\n{if is_extruder_used[3]}_PRIME_PH4{endif}\n{if is_extruder_used[4]}_PRIME_PH5{endif}\n\nUPDATE_DELAYED_GCODE ID=FILTER_FAN_OFF DURATION=0\nSET_FAN_SPEED FAN=filter_fan SPEED=1\n\n; Select initial tool\n{if initial_tool == 0}SELECT_PH1\n{elsif initial_tool == 1}SELECT_PH2\n{elsif initial_tool == 2}SELECT_PH3\n{elsif initial_tool == 3}SELECT_PH4\n{elsif initial_tool == 4}SELECT_PH5\n{endif}\n\nG92 E0 template_custom_gcode = thumbnails = 32x32/PNG, 400x300/PNG thumbnails_format = PNG toolchange_gcode = ; ProForge 5 toolchange G-code\n{if next_extruder == 0}\nSELECT_PH1\n{elsif next_extruder == 1}\nSELECT_PH2\n{elsif next_extruder == 2}\nSELECT_PH3\n{elsif next_extruder == 3}\nSELECT_PH4\n{elsif next_extruder == 4}\nSELECT_PH5\n{endif}\nG1 Z[layer_z] F24000 ; Move Z to the current layer height travel_lift_before_obstacle = 0,0,0,0,0 travel_max_lift = 0,0,0,0,0 travel_ramping_lift = 0,0,0,0,0 travel_slope = 0,0,0,0,0 use_firmware_retraction = 0 use_relative_e_distances = 1 use_volumetric_e = 0 variable_layer_height = 1 wipe = 0,0,0,0,0 z_offset = 0
[physical_printer:P5] host_type = moonraker preset_name = ProForge 5 preset_names = "ProForge 5" print_host = proforge5.local printer_technology = FFF printhost_apikey = printhost_authorization_type = key printhost_cafile = printhost_password = printhost_port = printhost_ssl_ignore_revoke = 0 printhost_user =
[presets] print = ProForge Default sla_print = sla_material = printer = ProForge 5 filament = PLA filament_1 = PLA filament_2 = PLA filament_3 = PLA filament_4 = PLA physical_printer = P5